I N S T A L L A T I O N IMPORTANT: BEFORE attempting to install and use the netboot package please read this whole text carefully! The most important word in the previous sentence is the word BEFORE, and the second important word is WHOLE! If you don't read this text carefully, and you blow up any of your systems, don't blame me. You have been warned... IMPORTANT: Even when cautiously following all instructions in this text it might be that something goes wrong. In this case, you can refer to a file called PROBLEMS in the same directory where you found the file which you are currently reading. PROBLEMS is like a FAQ and contains solutions to some of the more common problems. Overview of the installation process ==================================== Due to it's nature this package requires at least two computer systems. One acts as a server, and at least one other will be setup as a diskless client. Therefore this installation guide is divided into four sections: 1.) Compilation and installation of utility programs on the server 2.) Create a netbootable image of the target operating system 3.) Setup of the server 4.) Setup of the client including building the bootrom The server has to support TCP/IP and certain protocols based on this network standard. Most likely this will be a Unix-type server. Though it's probably possible to also use servers running OS/2 or Windows-NT, for example, all server related programs in this package can currently only be compiled on a Unix-type host. This requirement is independed of the operating system which is later booted on the diskless client. Therefore even if you want to boot MS-DOS on your client(s) you need at least one Unix-type computer for program compilation and generation of all boot files. Lateron when all necessary files are built you can use any server you want. This package contains two main parts: 1.) The bootrom source and binaries. This part gets installed on the diskless client. All binaries except those of utility programs are already precompiled. There are no further user changeable or adjustable options in the bootrom sources so you don't have to recompile the bootrom in order to use it. In order for the bootrom to access the network card in your diskless client you need a driver. Currently the bootrom supports packet drivers and NDIS drivers, which are normally used on DOS systems to interface a network stack with the hardware. With this package only the network driver binaries are required, so you don't need to recompile anything here as well. You can find precompiled packet drivers for many popular network cards on any SimTel FTP mirror (it's called Crynwr packet driver col- lection), and for those of you without internet access some of those packet driver binaries are included with this package. Another good source for a packet driver for your network card might be it's manufacturer. At least the well known manufacturers (3Com and SMC for example) provide packet drivers for their complete product line. Those manufacturer provided packet drivers are usually faster and easier to install than those from the Crynwr collection, and can often determine the hardware configu- ration at runtime, which some Crynwr drivers can't. You can use .COM and .EXE type packet drivers. Similarily, NDIS drivers are usually provided with your network card by it's manufacturer. On the driver disks you can often find NDIS drivers in a directory called LANMAN or NDIS. Be sure that you use an NDIS driver suitable for DOS, which complies to NDIS specification version 2.0.1 or older. NDIS drivers for Windows-95/-98 or Windows-NT/-XP (version 3.x of the NDIS specifi- cation or above) are not usable with netboot. You only need one network driver, either a packet driver or an NDIS driver. Since the packet driver interface within the bootrom is better tested than the NDIS interface as of yet, you might probably be better off first using a packet driver, if available. However, sometimes NDIS drivers are smaller and faster than packet drivers, so after testing with a packet driver it is recommended to also try using an NDIS driver when available. Lateron you can choose that one for a final bootrom which works best. 2.) A set of programs to generate netbootable images on the server. These programs are called mknbi-<os>, where <os> identifies the operating system which is lateron running on the diskless client. Currently only Linux and DOS are supported. For booting FreeBSD you don't need any mknbi-* program, as FreeBSD supports network booting right out of the box. There is another requirement which should not be left unnoted: the usual size of a bootrom will be between 16kB and 32kB (of course this depends on the size of the network driver). Therefore when you go shopping for a network card you should try to get one which is able to support at least 32kB EPROM's. This is standard on almost all cards from major manufacturers, but most cheap NE2000 are known to allow only a maximum of 16kB. Also note that some network cards from 3Com and SMC allow you to select ROM sizes of 32kB and more with their configuration programs, but can physically support only 16kB! Compilation and installation of utility programs on the server ============================================================== This package uses GNU's autoconf to configure the compilation process of the utility programs. You shouldn't have any problems to compile these programs on most Unix-type system. They have been tested on these systems with the generic C compilers: Linux 2.0.35 on x86 processor with glibc 2.0.1 Linux 2.4.20 on x86 processor with glibc 2.2.5 Linux 2.4.28 on Alpha processor with glibc 2.1.3 FreeBSD 4.4 on x86 processor SCO SysV 3.2 (ODT 5.0) on x86 processor SunOS 5.5.1 (Solaris) on Sparc 10 OSF/1 3.2 on Alpha processor AIX 4.1 on PowerPC IRIX 5.3 Proceed as follows to compile the utility programs on your system: 1.) Cd into the netboot directory and run ./configure. It's a configuration script generated by autoconf and checks for header files and system specific details. The mknbi utility programs contain some Intel assembler modules which lateron run on the diskless client. If you want to assemble these modules on your own you need a GNU C compiler (version 3.x or above) and the corresponding binutils. In case you are compiling the utility programs on anything different than x86 you will need an x86 cross compiler for the assem- bly modules. However, there are preassembled files included with this package, so you actually don't need any GNU tools. configure checks for the usability of any installed GNU development tools and creates the Makefiles accordingly. For an explanation of the command line switches available with the configure script just run it with the --help option. Some additional switches are: --disable-mknbi-linux --disable-mknbi-dos --disable-mknbi-mgl Choose these options if you don't want to create any of the corresponding mknbi utility programs. Unless you definitely know that you don't need any of these programs it is recommended to not use these switches. There is also another configure option: --enable-bootrom Use this option only if you want to recompile the bootrom itself. If you want to use the precompiled binaries, you don't need to specify this switch. See the file README.bootrom about how to recompile the bootrom. 2.) Check that all generated Makefiles and the config.h are correct for your system. 3.) Compile from within the main netboot directory with make clean make This will compile all programs without those which you disabled during the configuration stage. IMPORTANT NOTE: Some Makefiles use a syntax, which not every make program understands. If you get an error from make (usually in the form: "missing delimiter") then get and install GNU make on your system! Especially System V systems are known to have this deficiency. 4.) Permanently install the utility programs on your server with make install This will also install the corresponding man pages for later reference. Although it's possible to run all programs without installation, it's highly recommended to not skip this step. Otherwise you might loose some functionality, since all confi- guration files are created assuming permanent installation. Unless you didn't change the ./configure prefix, the installation step will create directories called /usr/local/lib/netboot and /usr/local/share/netboot, and copy almost all files into them. Only the executables get copied into /usr/local/bin, and the man pages go into /usr/local/man. Also, the major configuration file (netboot.config) will be copied to /usr/local/etc. Create a netbootable image of the target operating system ========================================================= This step of the installation process depends on which operating system you want to boot on your diskless clients. Everything described in this chapter does not depend on working on a Linux system. You can use any Unix type system to create the netbootable images. Most utility programs in this package offer a whole bunch of different runtime options, so that there are many different ways to achieve the same thing. The following descriptions explain how to work with the utilities using command line parameters. However, all of them also offer the possibility to use a database which holds all required information about client systems. This is especially useful when maintaining a larger base of diskless client systems. I recommend to first check out the installation instructions below. Lateron, when you got familiar with using all tools, read the netboot.db(5) man page, then read it again, then check the example database (misc/netboot.db.sample in the original netboot distri- bution) and then write your own system database, if you like. Linux: With Linux you have far too many options to list them all in this text. Please refer to the mknbi-linux(8) man page for all details. I will only describe the most common ways to setup a diskless Linux client here. First you have to decide where the Linux client is going to mount it's root filesystem from. This can either be a directory on an NFS server or a ram disk. Setup your Linux kernel accordingly. To use a root filesystem on an NFS server you should include TCP/IP network support into the kernel together with support for NFS file- systems. You cannot load this NFS support using a module as it has to be available at bootup. Additionally you also have to select NFSROOT and IP AUTOCONFIGURATION support during kernel configuration. However, you don't need BOOTP or RARP support. Accordingly if you want to use a ramdisk the filesystem type you are going to use on the ramdisk has to be permanently compiled into the kernel. Also initrd support has to be included in that case. Using an inapprop- riately configured kernel is the most common problem when trying to network-boot Linux. 1.) Configuring for NFS root filesystem. Next copy your Linux kernel into the current directory and run mknbi-linux: mknbi-linux -d rom -i rom -k zImage -o bootImage This supposes that your kernel image is called zImage, and gives you a netbootable image named bootImage. While mknbi-linux works with compressed and uncompressed kernels you should always use a compressed kernel for preformance reasons. 2.) Configuring for root filesystem on ramdisk If you want to use a ramdisk as a root device you have to create a ramdisk image first. Probably the easiest way to setup such an image is to use a floppy, though you can also use the loopback device if you are working on a Linux host. First format the floppy and make a filesystem on it, which is supported by the Linux kernel of your diskless client. Next copy all programs and files onto it which you want to have on the root filesystem of the diskless client lateron. You should then test your root floppy. To do this copy your kernel onto another floppy with dd and set it's root device to floppy using rdev: dd if=zImage of=/dev/fd0 rdev /dev/fd0 /dev/fd0 Now boot your diskless client using this boot disk. After the kernel started up, it will ask you to insert the root floppy and to press enter. Your root floppy will be mounted. If everything works as you intended, you can now create a netbootable image. Re-insert the root floppy into your server system and type: dd if=/dev/fd0 of=ramImage gzip -9 ramImage mknbi-linux -d ram -i rom -r ramImage.gz -k zImage -o bootImage Like above this will now give you a file bootImage with the netbootable Linux kernel image in it. FreeBSD: Network booting is supported right out of the box starting with FreeBSD version 4.x. In the directory /boot of your FreeBSD distribution you can find a file named 'pxeboot'. You can use this file as your boot image file without modification. DOS: To boot DOS on your diskless client you have to have MS-DOS Version 5.0 or higher. Windows-95 has an internal DOS called version 7.0, so it should be no problem to use it as well. Older MS-DOS versions will probably not work. OpenDOS, FreeDOS, DR-DOS and PTS-DOS also work depending on their version. A lot of efforts have been done on mknbi-dos to provide support for almost all available DOS clones, but it is still possible that some version might not work. First you have to create a directory which contains all the files the client will see on it's boot drive (either A: or C:). This can either be the root directory on a DOS floppy or any directory on the system on which you installed mknbi-dos. In the first case it has to be a floppy which contains a bootable DOS system, i.e. which has been created with format a: /s on a DOS system. If the directory resides on a UNIX system, you have to copy the two system files msdos.sys and io.sys, which are part of MS-DOS, into it by yourself. When using IBM-DOS or OpenDOS, these files are called ibmbio.com and ibmdos.com. To do this copying I recommend using mread of the MTools, which are freely available for almost every UNIX system (see your favorite GNU mirror for further information). After you created the directory or floppy which lateron becomes the clients boot drive, you should copy all other necessary files into it. This will probably include programs to setup a network environment on the client. When editing text files for the client please note that they usually have to be in DOS format with lines ending in Carriage-Return/Linefeed instead of just Linefeed as it is common on UNIX systems. If you start himem.sys from within config.sys you should be careful since newer versions of himem.sys (at least newer than 3.09) can destroy the ramdisk image in memory. If you have trouble starting DOS from the network but not from a boot diskette with the same setup, you should try to add the following switch to the himem.sys call: /testmem:off With OpenDOS, the himem.sys functionality is incorporated within emm386. However, this doesn't work with netboot. You still have to load both, himem.sys and emm386, for mknbi-dos to operate properly. The warning which will be printed by emm386 about himem.sys already being loaded can be safely ignored. This will eventually be corrected in future versions of netboot. When you are finished setting up the clients boot directory run mknbi-dos to create a netbootable image: mknbi-dos -r /dev/fd0 -o bootImage This assumes that you inserted the boot floppy into the fd0 drive of your UNIX system, and will create a file named bootImage. If you used a UNIX directory instead of a floppy disk, substitute /dev/fd0 with the name of that directoy. mknbi-dos will automatically detect if it is a directory, an ordinary file or a block device. By default mknbi-dos creates a netbootable image, which lateron mounts the ram disk as the A: drive on your client. If you want to mount the ram disk as C: instead, you should include the '-c' switch to the call of mknbi-dos. The difference between mounting the ram disk as a floppy (A:) or hard disk (C:) is, that with the floppy option the ram disk can be removed lateron, maybe after a network redirector has been loaded, which makes the ram disk obsolete. This is not possible with a virtual hard disk drive. On the other hand side, when using the ram disk as C: you can specify a different ramdisk size with the '-s' option. Please refer to the man page for mknbi-dos for further information. Setup of the server =================== Setup of the server depends on the kind of server you are using. There- fore all further explanations in this chapter can only serve as a general guide. You should consult your server's documentation as the final autho- rity. When the bootrom starts on the client it first tries to query a BOOTP or DHCP server for information like IP numbers and the name of the boot image file. Such a BOOTP server program is usually called bootpd. Alternatively, DHCP servers are commonly called dhcpd. Most SunOS servers use a program called bootparamd instead. Note that you _cannot_ use bootparamd as a substitute for bootpd or dhcpd as it uses a different protocol. Install a publicly available bootpd instead on your sun. Next you should copy the bootImage file, which you have created in the previous step above, into a publicly accessible directory (called /boot for example). If you want to boot more than one diskless client you can use the same bootImage file for all clients, provided that these clients use similar hardware. However, if you configured for a ramdisk (with Linux or DOS) and the ramdisk image contains different files or information for each client, you will obviously also need a different bootImage file for each client. Then you need to setup a boot description file for bootpd, which is usually called /etc/bootptab. Consult your server's documentation for further information. However, the entries in this file will usually look something like this for every diskless client: client1:hd=/boot:vm=auto:ip=184.108.40.206:\ :ht=ethernet:ha=004001417173:\ :bf=bootImage-client1:rp=/boot/client1/root 'hd' specifies the home directory and 'bf' is the name of the bootImage file, which you created in the previous step. Therefore the full pathname for the bootImage file for the diskless system called "client1" will be /boot/bootImage-client1 with this sample entry. The 'ip' tag specifies the IP address of the client, 'ht' the type of the network the client is attached to, and 'ha' it's hard- ware address. The 'vm=auto' tag tells bootpd to use the same vendor encoding as the bootrom. If your diskless client is going to use it's root filesystem via NFS you should also specify the directory on the server which gets mounted lateron with the 'rp' tag. However, if your diskless client uses a ramdisk, you can omit 'rp'. The format of the configuration file required for your BOOTP or DHCP server might be different from the above sample, so you should carefully read all documentation which comes with your server. Of course you should also remember to get bootpd or dhcpd running on the server, either on bootup from /etc/rc or some similar mechanism, or from inetd. Again, see your server's documentation about how to do this. Note that after starting bootpd, it is usually required to send it a HUP signal whenever you have changed /etc/bootptab. Some DHCP servers even need a complete restart when their configuration files have been changed. The next step preformed by the bootrom after querying the BOOTP server is to load the boot image file specified by the 'hd' and 'bf' tags in /etc/bootptab. To do this a protocol named TFTP is used. Therefore you will next have to setup a daemon process for this protocol on your server. Such a daemon is usually called tftpd, and you should again remember to get tftpd running, usually via inetd. Since the TFTP protocol is very insecure, access to the tftpd server is usually restricted, either within tftpd itself, or with a TCP/IP wrapper like tcpd. tcpd for example uses host access control tables which are stored in /etc/hosts.allow and /etc/hosts.deny. See tftpd(8), tcpd(8) and hosts_access(5) as well as your server's documentation for further information. If you selected a ramdisk for the diskless client's root directory you are now finished with the server setup. But if your client is going to use NFS (either directly like with booting Linux, or by using programs included on the ram disk) or if you want to boot FreeBSD (which requires NFS as there is no ramdisk support available) you should now setup everything which is necessary for mounting an NFS directory on the server. This usually involves running several programs: portmap, mountd, nfsd and optionally ugidd. portmap usually doesn't require editing any configuration files. But for mountd and nfsd you need to specify the permissions which allow the client to access the required directories on the server. These permissions are usually set with a file called /etc/exports. Typically it looks like this for our sample client: # # Export directories for client1 (diskless workstation) # /boot/client1/root client1(rw,link_absolute) /boot/client1/usr client1(rw,link_absolute) If you use 'map-daemon' to map UID and GID numbers on the server you should remember to also configure and run ugidd on the server. Please consult your server's documentation for further information regarding setup of NFS exports. You might also want to check out the portmap(8), nfsd(8), mountd(8) and ugidd(8) man pages. Also remember that access to any of these services might be restricted with tcpd on your server. Another important step is to fill up the root directory for the disk- less client. It has to contain all files necessary for the client to startup and mount further directories via NFS (like a /usr filesystem as specified in the /etc/exports example above). How to setup this root directory is far beyond the scope of this documentation. Just one hint: if your server is _not_ running the same operating system as the client you are going to boot, you should be aware of major/minor number assignments in the /boot/client1/root/dev directory. For example, simply using mknod on an AIX server will eventually give you wrong major/minor number when the directory is later exported to a Linux diskless client. With some configurations AIX will add a certain offset to all major numbers which makes them unusable for Linux. Refer to your server's manuals for further information. You might also find some useful hints in the file Documentation/nfsroot.txt in the Linux source tree, if your diskless client is booting Linux. Also, the PROBLEMS file in this package contains some useful hints when you run into any major/minor number or other NFS problems. When booting FreeBSD it is important to copy the kernel file (which can be found in the root directory of a FreeBSD client) onto the server into /boot/client1/root or wherever your client's root directory lies on the server. Also, the /boot directory of the FreeBSD client, which is going to be mapped via NFS to /boot/client1/root/boot on the server, has to be valid. It should contain all the files which come with your FreeBSD distribution in this directory. Setup of the client including building the bootrom ================================================== Until now you only had to work on the server (with the exception of maybe booting your diskless client from a diskette to check the correctness of the root filesystem). As the last step we can now go on and setup the diskless client itself. The first step is to configure the network card in the diskless client. For this refer to the manual which came with the network card. Some cards require setting some jumpers. Others have setup programs which have to be run. After configuring the network interface write down all necessary hardware parameters like I/O addresses, memory addresses, interrupt line number or DMA channel numbers, as you might need this information lateron in the configuration process. Also make sure, that you enabled PnP and/or PCI support in the client BIOS setup when you are using an ISA-PnP or PCI network card. The network card has to be properly configured by the BIOS _before_ the bootrom starts and _before_ any operating system gets loaded. There is no way of running an ISA-PnP configuration utility from within the bootrom. Next go back to your UNIX-type server and copy all network drivers for your network card into the main netboot directory. Packet drivers should go into /usr/local/share/netboot/netdrvr/pktdrvr, and NDIS drivers should be copied into /usr/local/share/netboot/netdrvr/ndis2, or wherever you permanently installed netboot. Then run makerom in any directory to start the bootrom configuration program. It will first ask you about certain characteristics of the final bootrom. Usually, you can just accept the default answer by pressing <enter>. For a further explanation of all the questions asked by makerom refer to it's man page or it's builtin help function. It will then print you a list of known network cards. Choose a description from this list which matches your network card as close as possible. This is extremely important! For example, SMC produced different network cards which are all 8013 compliant, but which require different parameters for the network driver configuration. They can be distinguished by their postfix (8013EB, 8013EBT, 8013S etc.). As another example, Accton produced network cards with the same number (1207) but with different and incompatible chip- sets. A final example: even though many cheap PCI network cards are claimed to be NE2000 compatible they require a different bootrom and driver confi- guration than a true NE2000 and ISA-NE2000-compatibles. Therefore, it can't be stressed enough that you have to select a network card from the list which fits your card as exactly as possible. If your network card is not in the list printed by makerom, you should choose 0 which means "unknown network card or unsupported network driver". In this case makerom will next ask you about which type of network driver interface you want to use. Select the one which is supported by your network driver. Then enter the path name of that network driver. You will then have to enter a command line for a packet driver, or the name of a protocol.ini file for an NDIS driver: - Packet driver command line: enter all command line options required by your packet driver (without the packet driver file name). Please refer to the documentation which comes with the driver. Also, most packet drivers print the command line options they know about when you run them without any options under DOS. Don't specify any options here which switch the driver into windows mode or which allow it to work for diskless systems or bootroms. Those options are for Novell network bootrom setups only, and are not necessary for the netboot bootrom. - NDIS protocol.ini file: NDIS drivers require a resident utility called protocol manager when run on a DOS system. This protocol manager is responsible of providing configuration data to the NDIS driver and connecting it to a protocol stack (like a TCP/IP stack). The NDIS driver interface of the netboot bootrom contains a protocol manager simulator, so you don't need the actual protocol manager program. However, like the real protocol manager, the simu- lator also needs a protocol.ini file. This file will be parsed by makerom and included into the bootrom in a compressed binary format. Since the bootrom knows what protocol stacks are available within itself, the protocol.ini file for netboot only requires the information for configuring the NDIS driver. See the makerom man page for a short description of the format of a protocol.ini file. It consists of sections, each prepended by a section name enclosed in square brackets. For the netboot bootrom, only the section is required which contains the NDIS driver configuration information. This information is organized in parameter values, with each parameter on a seperate line. Following a parameter name comes an equal sign and the parameter value. See the docu- mentation of your NDIS driver about which parameters it under- stands. However, at least the drivername parameter has to appear in every NDIS driver configuration section. For example, a minimal protocol.ini file for an Accton EN1207D network card should look like: [accnd] drivername = accnd$ The name of the section is unimportant, but the value of the drivername parameter has to be exactly as required by the NDIS driver. Some drivers might need additional parameters like I/O addresses, memory addresses, buffer sizes etc. If your network card is in the list of cards known, then you can just enter it's number. You don't have to worry about packet driver command lines and protocol.ini files in that case. If more than one driver is available for your card, makerom will print a list of available drivers, and you can select one. It will then ask you about all necessary hardware information to provide to the network driver. Especially for ISA cards, this might include the I/O address of the network card, it's interrupt number and a DMA channel number. Note that only that information is requested which is really necessary for the network driver selected. You should have your network card information handy when entering this infor- mation. Some network drivers (especially for PnP and PCI network cards) are able to determine hardware related information at runtime and there- fore don't require any further information to be entered. When you are using a packet driver, makerom will next ask you if you want to include the packet driver debugging program. That's an additional module to trace network problems and is usually not required. It shows you the first couple bytes of all packets (where the UDP/IP headers are encoded) going through the packet driver during boot time of the diskless client. Only select this debugging module if you run into problems during the initial network boot process of the bootrom _and_ you know how to decode the UDP/IP header information. Otherwise do not include this debugger. makerom will also ask you about any additional modules you want to install into the bootrom. These modules have to be standard DOS COM- or EXE-type programs, and can, for example, enhance special features of the network driver. However note that the total size of the resulting bootrom image can't be larger than 128kB. Finally makerom will ask you what kind of output file you want to create. Choose the type which your EPROM burner understands. The most likely choice will be "raw binary" or "intel hex" but better check your burner's manual first. If you don't want to burn an EPROM, don't worry and choose anything, since the floppy boot image always gets generated (see below). You probably don't want to create a "flash" binary at this stage. See below for further information about Flash-EPROM usage. After you answered all questions makerom is creating the bootrom according to your specifications. It first combines the bootrom kernel with all selected modules, then compresses the resulting file and adds the bootrom startup code. When it has finished you will find two new files in the current directory: image.flo - this file can be written onto a floppy using dd and either one of image.rom - raw binary image to be burned into an EPROM image.hex - hex encoded image to be burned into an EPROM image.flash - ROM image to be used for remote programming of a FlashCard At first you will probably _not_ need the file image.flash. See below for further information about flash memory and FlashCard. You should now copy image.flo onto a floppy using dd if=image.flo of=/dev/fd0 conv=sync and then boot your diskless client using this floppy. If you have setup everything (including your network card) you will see the bootrom code starting, querying the BOOTP server and loading the boot image file. When everything works as required you can then go on and burn the file image.rom or image.hex into an EPROM. Please consult the manual of your EPROM burner how to do this. Insert the burned EPROM into the socket on your network card and turn on the diskless system. You should now see the bootrom coming up. If not, but the bootrom works when started from a floppy, your BIOS might not be able to recognize the EPROM properly. In this case you might want to use the romcheck program which allows you to inspect the ROM area in your client. Refer to the file README.romcheck for further information. Another way of getting the bootrom code into your client is using the Flash-EPROM card (called FlashCard), for which you can find a schematic and PCB layout in this package. You can use the raw binary image (image.rom) directly to burn it into FlashCard, but it's much easier to use the special flash image format (image.flash), which can be created by makerom. If you have built a FlashCard and installed it into your client, proceed as follows: 1.) Copy the file image.flash into a directory which is accessible by TFTP on your server 2.) Edit /etc/bootptab so that the client will load image.flash instead of the normal boot image file. Usually, this means changing the 'bf' setting in the client's bootptab entry. Re- member to send a HUP signal to your bootpd process if it's running permanently. Alternatively you can also set 'bf' to a soft link, and let that link point either to the normal boot image file, or image.flash in case of programming the FlashCard. Then you just need to change the link, and not to edit bootptab. Proceed accordingly if you are using a DHCP server. 3.) Copy the file image.flo onto a bootable floppy as described above 4.) Boot your client using this floppy. This will start the bootrom code on the floppy, which will then load the image.flash file and program it's contents into the FlashCard. Once you initialized the FlashCard like this you can skip step 3 for future bootrom upgrades. 5.) Restore the old 'bf' entry in your /etc/bootptab file on the server or let the soft link point back to the original boot image file. Again, remember to send a HUP signal to your per- manently running bootpd (if applicable). Some network cards have a flash EEPROM already installed on the network card. For some of those cards, makerom is also able to produce a flash image which you can use exactly in the same way as described above. The only difference is that you don't need to make yourself a FlashCard. Another alternative is to put the bootrom code directly into the main system BIOS, for example to replace a commercial PXE bootrom code. makerom can produce a binary bootrom image which you can use this way, but the exact steps to perform this BIOS inclusion are beyond the scope of this document. Refer to the netboot home page at http://netboot.sourceforge.net for further information. Also, re- designing and programming your own system BIOS is risky and dangerous, so you should have pretty much knowledge about what you are going to do, because you can easily make your system completely useless. Finally it might be worth mentioning that you can also put the floppy image (e.g. image.flo) onto a bootable hard disk partition. This way, you can start netboot without having to burn an EPROM but with a hard disk installed. Simply create an empty bootable partition. Then you can copy image.flo into that partition, for example using dd if you have Linux running on your client, or some other program like the Norton Utilities. Appendix: Adding a menu ======== After you got the remote boot process running you might consider to implement a boot menu. With such a menu you can let the user select an operating system to boot, either from the network or from a local storage media. You can even simplify updating a FlashCard to a new bootrom version by using a menu option. Please refer to the file README.menu for further information. Appendix: Recompiling the bootrom ======== If you want to recompile the bootrom for some reason, checkout the file README.bootrom for further information. However, you don't need to re- compile the bootrom in order to just use it!
Back to the last page
Created automatically from source file INSTALL by getdoc on Wed Mar 21 09:04:45 UTC 2018